“Keep your AR15 BCG running like new with AR15 BCG Maintenance 101!”

The Basics of AR15 BCG Maintenance: What You Need to Know

AR15 BCG (Bolt Carrier Group) maintenance is an important part of keeping your rifle in top condition. Proper maintenance will ensure that your rifle functions reliably and safely. Here are the basics of AR15 BCG maintenance that you need to know.

First, you should inspect your BCG regularly. Look for any signs of wear or damage, such as cracks, chips, or gouges. If you find any, replace the BCG immediately.

Second, you should clean your BCG regularly. Use a brush and solvent to remove any dirt or debris from the BCG. Make sure to clean the firing pin, extractor, and other components as well.

Third, you should lubricate your BCG regularly. Use a high-quality lubricant designed for firearms. Apply a thin layer of lubricant to the BCG and its components.

Fourth, you should check the headspace of your BCG. This is the distance between the bolt face and the chamber. If the headspace is too large, it can cause malfunctions.

Finally, you should check the gas rings on your BCG. These rings help seal the gas system and prevent gas from escaping. If the rings are worn or damaged, replace them.

By following these basic steps, you can ensure that your AR15 BCG is in top condition and ready to perform when you need it. Proper maintenance is essential for reliable and safe operation of your rifle.

Step-by-Step Guide to Cleaning and Lubricating Your AR15 BCG

Step 1: Disassemble the BCG

Before you begin cleaning and lubricating your AR15 BCG, you must first disassemble it. To do this, you will need a punch and a hammer. Start by removing the firing pin retaining pin. This pin is located at the rear of the BCG and is held in place by a small spring. Once the pin is removed, the firing pin and its spring can be removed. Next, remove the cam pin, which is located at the top of the BCG. Finally, remove the bolt carrier from the bolt.

Step 2: Clean the BCG

Once the BCG is disassembled, it is time to clean it. Start by using a brush to remove any dirt or debris from the BCG. Next, use a cloth and a cleaning solvent to wipe down the BCG. Make sure to pay special attention to the bolt and bolt carrier, as these are the parts that will be in contact with the ammunition. Once the BCG is clean, use a dry cloth to remove any remaining solvent.

Step 3: Lubricate the BCG

Once the BCG is clean, it is time to lubricate it. Start by applying a thin layer of lubricant to the bolt and bolt carrier. Make sure to cover all surfaces of the bolt and bolt carrier. Next, apply a thin layer of lubricant to the cam pin and firing pin. Finally, apply a thin layer of lubricant to the exterior of the BCG.

Step 4: Reassemble the BCG

Once the BCG is lubricated, it is time to reassemble it. Start by inserting the bolt carrier into the bolt. Next, insert the cam pin and firing pin into the BCG. Finally, insert the firing pin retaining pin and its spring into the rear of the BCG.

Step 5: Test the BCG

Once the BCG is reassembled, it is time to test it. Start by inserting a magazine into the AR15 and chambering a round. Pull the trigger to ensure that the BCG is functioning properly. If the BCG is functioning properly, you are now ready to use it.

Congratulations! You have now successfully cleaned and lubricated your AR15 BCG. With proper maintenance, your BCG should provide you with years of reliable service.

Common AR15 BCG Maintenance Mistakes to Avoid

When it comes to maintaining an AR15 BCG (Bolt Carrier Group), there are some common mistakes that should be avoided. These mistakes can lead to malfunctions, damage, and even injury. Here are some of the most common AR15 BCG maintenance mistakes to avoid:

1. Not cleaning the BCG regularly: It is important to clean the BCG regularly to ensure that it is functioning properly. This includes removing any dirt, debris, and carbon buildup.

2. Not lubricating the BCG: Proper lubrication is essential for the BCG to function properly. It is important to use the correct lubricant and to apply it in the right amounts.

3. Not inspecting the BCG: Regularly inspecting the BCG is important to ensure that it is functioning properly. This includes looking for any signs of wear or damage.

4. Not replacing worn or damaged parts: If any parts of the BCG are worn or damaged, they should be replaced immediately. This will help to ensure that the BCG is functioning properly and safely.

5. Not using the correct tools: Using the correct tools is essential for proper maintenance of the BCG. This includes using the correct torque wrench and other tools for disassembly and reassembly.

By avoiding these common AR15 BCG maintenance mistakes, you can help to ensure that your BCG is functioning properly and safely.